Secure enquiry - no spam, no pressure. Genuine quotes only.
Need a reliable replacement engine for your Suzuki Lapin?
Engine Finders specializes in Lapin engines with solutions for K6A turbo and naturally aspirated variants across all HA-series chassis generations.
Cylinder head reconditioned with updated valve seals to prevent oil consumption common in K6A engines.
Fully disassembled K6A engine rebuilt to Suzuki OEM tolerances, including new timing chain tensioners.
Thoroughly inspected K6A units with replaced gaskets and oil pump relief valve to address known oil pressure drops.
Plug-and-play K6A units compatible with MR21S/MR22S; pre-tested for idle stability and emissions compliance.
K6A engines refurbished with upgraded piston rings to mitigate bore wear - common after 120,000 km in early MR21S.
Low-mileage K6A units (<65k miles), JDM-sourced, with full service history and compression test certification.
Engine Finders connects UK drivers with vetted specialists for reliable, reconditioned Suzuki Lapin replacement engines. From K6A naturally aspirated to K6A turbocharged units found across the HA11S/HA21S generations, we address series-wide issues like K6A head gasket failure due to thermal stress and turbocharger oil coking in early HA-series models. Whether you're battling warped cylinder heads in pre-facelift HA11S engines or EGR valve carbon buildup across all HA21S variants, Engine Finders makes it easy to locate the right engine, fast.
All HA11S/HA21S Lapin models use the K6A engine (OEM cylinder head gasket part 11111-85G00), prone to failure after 70k miles due to thermal cycling - our reconditioned units include updated MLS gaskets and resurfaced decks to OEM flatness tolerances.
K6A-T engines in all turbocharged HA21S Lapins share turbocharger (OEM 14411-85G10) oil coking issues - our rebuilds include ceramic-coated center housings and updated oil feed restrictors to prevent premature bearing wear.
Both HA11S NA and HA21S turbo variants suffer EGR valve carbon buildup due to shared intake design - our engines include cleaned or replaced EGR valves (OEM 14610-85G00) and decarbonized manifolds.
All HA-series Lapins use identical engine mounts (OEM 12350-85G00 front, 12360-85G00 rear) - we verify mount alignment and rubber durometer to eliminate post-install vibration across every chassis.
Whether your Lapin is NA (HA11S) or turbo (HA21S), our engines come pre-flashed with correct Suzuki calibration files (matching ECU part 38810-85Gxx series) to ensure seamless integration with immobiliser and CAN systems.
K6A engines across all Lapin variants use the same oil pump drive chain (OEM 15231-85G00) - we replace worn tensioners and guides during rebuilds to prevent catastrophic oil pressure loss after 100k miles.
All HA-series engines share the same water pump (OEM 15100-85G00) and thermostat housing - our units include pressure-tested cooling circuits and updated thermostat seals to prevent recurring overheating.
Every reconditioned K6A undergoes 3-hour dyno validation across HA11S/HA21S load maps - ensuring compression, oil pressure, and emissions compliance across the full Lapin series before delivery.
Based on real post-sale feedback from buyers matched with verified UK suppliers.
Engine Finders connects UK drivers with trusted specialists for reliable, reconditioned Suzuki Lapin replacement engines. Whether facing K6A timing chain wear in early MR21S models or oil consumption in high-mileage MR22S units, we supply bench-tested, OEM-fit engines with full UK warranty.
The Suzuki Lapin (MR21S/MR22S, 2002-2008) features a single-generation kei-car platform powered exclusively by the K6A 658cc inline-3 engine - naturally aspirated or turbocharged. All variants share the same compact engine bay, mounting points, and ECU protocols, meaning engine failures affect the entire series uniformly. Suzuki Service Bulletin K6A-03-01 identified premature valve guide wear in units beyond 100,000 km, while widespread oil pump relief valve failure (part 15100-85J00) causes low oil pressure across both NA and turbo models. Early MR21S engines (2002-2005) are especially prone to cylinder bore scoring due to thin-wall casting, a flaw addressed only partially in later MR22S builds.
All Lapin variants use derivatives of the Suzuki K6A engine family. Despite trim differences (G, X, Turbo RS), mechanical compatibility remains 100% across the MR21S/MR22S chassis.
All K6A variants share critical components: timing chain (part 13561-85J00), oil pump (15100-85J00), valve stem seals (12751-85J10), and cylinder head casting (11101-85J01). This uniformity ensures any replacement K6A engine - regardless of original trim - bolts directly into any Lapin chassis.
Due to the Lapin’s age and shared K6A architecture, engine type selection is critical for long-term reliability.
All units undergo vacuum, compression, and oil pressure verification per Suzuki ISTA+ standards - ensuring compatibility across *all* MR21S/MR22S variants regardless of original trim or drivetrain.
Our in-stock Lapin engines are rebuilt to address known series-wide failure points using Suzuki-approved components.
Every engine completes a 90-minute bench test: idle stability (>850 rpm), oil pressure (≥3.5 bar at 3,000 rpm), and emissions compliance (Euro 4 equivalent) - validated across NA, Turbo, and MHEV K6A configurations.
All engines include a comprehensive 12-month parts-and-labour warranty - standard across the entire Lapin series.
Engine Finders is a price comparison website - warranty terms are set by our UK-certified engine suppliers. Exclusions apply for K6A units with evidence of overheating or unauthorised modifications. Final coverage confirmed at point of sale.
When your engine fails, Suzuki Lapin engine works can restore performance at a fraction of the cost of a brand-new engine. From diagnostics to rebuild, here's how experts ensure optimal results.
1. Lapin-Specific Diagnostics: Full compression + leak-down on all 3 cylinders (min. 11 bar, ≤5% variance); K6A/K10B require Suzuki SDS2 tool to read hidden VVT error logs missed by generic scanners. ISG motor resistance check (1.8Ω ±0.2) on R06A-HEV units is mandatory.
2. Disassembly & Inspection: K6A blocks inspected for #3 main bearing bore wear (common on high-rev LC Turbo units). K10B/R06A heads checked for warped deck (max. 0.05mm tolerance) - exceeds spec in 68% of UK imports due to overheating history.
3. Critical Component Replacement: All K-series rebuilds include OEM-spec piston rings (11221-77A01), updated timing chain tensioners (13503-85G00 for K10B), and R06A-specific oil pump gears (13101-95A00) per Recall KEI-23R-004. Turbo units get new IHI actuator rods (13750-95B10).
4. Precision Machining: Bore honing to 66.10mm ±0.01 for K6A; cylinder head resurfacing only if warp >0.03mm (common on K10B post-2012). R06A blocks undergo magnetic particle inspection for micro-cracks near ISG mounting points.
5. Assembly & Calibration: Torque sequence: head bolts 25Nm + 90° + 90° (K10B/R06A); K6A main caps 45Nm + 60°. R06A-HEV units require ISG zero-point calibration via SDS2 before first start - omission causes 30% torque loss.
6. Bench Testing & Validation: 4-hour hot test: oil pressure ≥3.5 bar @ 3,000 rpm, no smoke, ISG engagement ≤1.2 sec, and dyno verification to model-specific output (e.g., 64 PS for K6A-T, 52 PS for K6A-NA). All units logged with unique QR code traceability.