Secure enquiry - no spam, no pressure. Genuine quotes only.
Need a reliable replacement engine for your Suzuki Kizashi?
Engine Finders specializes in Kizashi engines with solutions for common timing chain and oil consumption issues across all variants.
Includes upgraded piston rings and main seals to address common oil consumption in J24B engines.
Complete teardown with OEM-spec CNC machining; resolves valve seat wear prevalent in high-mileage J24B units.
Compression-tested and oil-pressure-validated; ideal for resolving timing chain rattle in pre-2012 GW/GY models.
Plug-and-play J24B units - no reprogramming needed. Direct fit for all GW/GY chassis years (2009-2016).
Includes new water pump and thermostat housing - addresses known coolant leak points in GW/GY engine bays.
Low-mileage J24B units (≤75k miles), full service history, compression & leak-down certified. Ideal for budget repairs.
Engine Finders connects UK drivers with vetted specialists for reliable, reconditioned Suzuki Kizashi replacement engines. From the J24B 2.4L petrol engine found across all Kizashi trims (G, SE, SLS) to shared timing chain and oil consumption issues affecting the entire series, we provide series-validated solutions. Whether you're battling premature timing chain wear or excessive oil consumption common to all Kizashi models from 2009-2016 due to piston ring design (OEM 13150-87J00), Engine Finders ensures you get the right engine fast - with technical precision matched to your chassis.
We replace the tensioner (OEM 13165-87J10) and guide rails across all Kizashi variants using Suzuki Service Bulletin KZ-12-03-compliant parts to eliminate premature chain rattle found in every model from 2009-2013.
All Kizashi models (G, SE, SLS) use the same J24B short block prone to oil burning; we upgrade piston rings (OEM 13150-87J00) and valve stem seals (OEM 13751-87J00) in every reconditioned engine to meet revised Suzuki durability standards.
Every Kizashi (2009-2016, all chassis codes) shares identical engine mounts (OEM 11230-87J00); our replacements include reinforced rubber compounds to reduce NVH without compromising OEM alignment geometry.
The J24B’s variable valve timing (OEM 13505-87J00) suffers from solenoid clogging across all trim levels; we clean and recalibrate VVT phasing to Suzuki ISTA+ specifications for seamless ECU integration.
The J24B’s integrated water pump (OEM 17100-87J00) fails at ~100k miles in every Kizashi variant; we install upgraded ceramic-seal units with extended-life bearings as standard in all rebuilt engines.
Whether your Kizashi is a base G or top-spec SLS, we provide correct ECU compatibility (including immobiliser sync) using Suzuki TechInfo protocols - ensuring plug-and-play start-up without dealer dependency.
Every replacement engine includes a 12-month unlimited-mileage warranty - backed by specialists trained on the entire Kizashi range (2009-2016), not just isolated variants.
We connect you with the only UK supplier network holding verified J24B cores across all Kizashi trims - ensuring faster sourcing, accurate matching, and £300-£800 savings vs. dealer quotes.
Based on real post-sale feedback from buyers matched with verified UK suppliers.
Engine Finders connects UK drivers with trusted specialists for reliable, bench-tested Suzuki Kizashi replacement engines. Whether resolving J24B timing chain wear across all GW/GY models or addressing oil consumption in high-mileage units, we supply direct-fit, MoT-compliant solutions.
The Suzuki Kizashi (GW/GY, 2009-2016) was Suzuki’s sole D-segment sedan, powered exclusively by the 2.4L J24B inline-4 across all trims and drivetrains. Despite its robust design, shared architecture led to consistent failure points: pre-2012 models suffer from timing chain tensioner wear (Suzuki TSB KZ-10-07), while 2012-2016 units exhibit increased oil consumption due to piston ring land wear. All variants use identical engine mounts, ancillaries, and ECU mapping - enabling direct interchangeability regardless of trim (SE, Sport, AWD) or transmission (6MT/6AT).
Only one engine family powered the entire Kizashi range in the UK:
OEM part harmonisation means engines are fully interchangeable between FWD and AWD variants. Critical shared failure components include timing chain tensioner (95520-85J00), VVT actuator (18210-85J00), and oil pump pickup tube gasket (15271-85J20).
We supply six engine types - each tailored to the J24B’s known failure patterns:
Every unit undergoes bench compression, oil pressure, and leak-down testing before dispatch - ensuring OEM-spec performance for the entire Kizashi range.
Our reconditioned J24B engines include standard upgrades addressing the most prevalent Kizashi concerns:
Each engine completes a 2-hour bench run simulating idle-to-redline cycles, with oil pressure verified at 45+ psi (hot idle) and compression within 12-14 bar across all cylinders.
All engines include a 12-month parts-and-labour warranty covering internal components, seals, and electrical ancillaries.
Engine Finders is a price comparison and referral service. Warranty terms are set exclusively by our vetted UK engine suppliers in accordance with Consumer Rights Act 2015. Final coverage is confirmed at point of purchase.
When your engine fails, Suzuki Kizashi engine works can restore performance at a fraction of the cost of a brand-new engine. From diagnostics to rebuild, here's how experts ensure optimal results.
1. Disassembly & Inspection: J24B engines are fully stripped using Suzuki Special Tool 09923-23010 for cam sprocket removal. Critical checks: bore taper (max 0.03mm), cam lobe wear (min 38.2mm lift), and timing chain stretch (max 1.2% elongation per WIS).
2. Block Refurbishment: Block is hot-tank cleaned, then pressure-tested at 15 psi for 10 mins. Cylinder honing to 0.0025" RA finish with plateau honing for GF-chassis oil control rings (OEM spec 11020-85J00). Main bearings resized only if wear >0.05mm.
3. Head Reconditioning: Heads CNC-milled (max 0.15mm removal), valves refaced (30°/45° angles), and new OEM-spec guides pressed (part #13241-85J00). Critical: VVT solenoid screens replaced (OEM #14241-85J01) per TSB ENG-2016-09 to prevent oil starvation.
4. Rotating Assembly: New OEM-spec pistons (part #12111-85J10) and rings installed - top ring gap set to 0.35-0.45mm. Crankshaft reground only if journals exceed 0.025mm out-of-round; all rods balanced to ±2g for smoothness at 6,000 rpm.
5. Timing & Assembly: Timing set with Suzuki Tool 09923-23020 - crank at TDC, cams aligned to GF-specific marks (not SX4). Bolt torque: head 25Nm + 90° + 90° (two-stage angle tightening), cam caps 10Nm in sequence per WIS 01-412.
6. Testing & Calibration: Bench-run 45 mins: idle stability (±50 rpm), oil pressure ≥4.2 bar @ 2,000 rpm, no misfires. Final ECU flash with Kizashi-specific file (0261S00254) to reset adaptation and prevent limp mode on first drive.