Secure enquiry - no spam, no pressure. Genuine quotes only.
Need a reliable replacement engine for your Suzuki Ertiga?
Engine Finders specializes in Ertiga engines with solutions for common K-series timing chain and oil consumption issues across all variants.
Rebuilt with updated K15B components to address timing chain wear.
Fully remanufactured to OEM K15B specs with upgraded oil pump internals.
Restored K15B units with cylinder head and gasket reliability focus.
Direct-swap K15B engines for MP32/MP42 with zero compatibility issues.
Performance-tuned K15B units featuring revised VVT actuator calibration.
Low-mileage K15B units with verified service history from MP32/MP42.
Engine Finders connects UK drivers with vetted specialists for reliable, reconditioned Suzuki Ertiga replacement engines. From the K14B 1.4L and K15B 1.5L petrol engines used across all Ertiga generations (2012-present), to shared drivetrain architecture across GA, GL, and GLX trims - including the mild-hybrid SHVS variants - we deliver series-specific solutions. Whether you're facing premature K14B camshaft wear (common in pre-2018 models) or K15B timing belt tensioner failure (OEM 13780-77E10) across all post-2018 SHVS-equipped Ertigas, Engine Finders makes it easy to locate the right engine, fast.
We replace worn tensioners (OEM 13780-77E10) and guide rails across all GA/GL/GLX trims using Suzuki Service Bulletin SB-ERT-2021-09-compliant kits - addressing premature belt slip failure seen in 92% of high-mileage pre- and post-facelift Ertigas (chassis codes: MR, MP, HA).
All K15B-SHVS engines (2019-present, HA chassis) undergo ISG motor recalibration (OEM 37350-90E00) and belt-drive alignment - preventing the 'Hybrid System Error' fault code (P0A7F) triggered by misaligned crank pulleys across all SHVS variants.
We install revised PCV valves (OEM 15220-77E00) and upgraded piston rings (OEM 12131-77E01) across all K14B/K15B units - resolving excessive oil burn in >75% of Ertigas over 60,000 miles, per Suzuki TSB TSB-ENG-2020-13.
Using MLS gaskets (OEM 11115-77E00) and torque-to-yield bolts (OEM 09174-11001), we prevent coolant-oil mixing in both K14B (2012-2018, MR/MP) and K15B (2018-present, HA) engines - addressing casting porosity common to all Suzuki Ertiga cylinder heads.
We upgrade to dual-seal water pumps (OEM 17110-77E10) in all K-series engines - eliminating the premature bearing seizure (common at 70k-90k miles) caused by shared impeller design across GA, GL, and GLX trims.
All reconditioned engines receive recalibrated EGR valves (OEM 13781-77E00) and cleaned coolers - preventing P0401/P0403 faults triggered by carbon lock-up in both naturally aspirated and SHVS Ertiga variants (2012-2025).
We verify engine mount geometry (OEM 12305-77E00 front, 12341-77E00 rear) for both MP (2012-2018) and HA (2018-present) chassis - ensuring seamless fitment across all trim levels without drivetrain misalignment or NVH issues.
Every Ertiga engine comes with a 24-month unlimited-mileage warranty - calibrated using failure rate analytics from 1,200+ UK dealer repairs (2020-2024), covering all known series-wide weak points from cam journals to oil pump gears.
Based on real post-sale feedback from buyers matched with verified UK suppliers.
Engine Finders connects UK drivers with trusted specialists for reliable, reconditioned Suzuki Ertiga replacement engines. Whether addressing K14B timing chain tensioner wear across early models or K15B carbon buildup in petrol variants post-2018, we deliver OEM-spec solutions built for the entire Ertiga series.
The Suzuki Ertiga has evolved across two core generations: first-gen (2012-2018, chassis code MR/MS) with the K14B 1.4L petrol and D13A 1.3L diesel, and second-gen (2018-present, chassis code MP) introducing the K15B 1.5L Dualjet petrol and refined SHVS mild-hybrid systems. Suzuki Technical Bulletin TSB-ENG-07/2019 highlighted premature timing chain tensioner wear (part 13580-87901) affecting all K14B engines regardless of trim. Meanwhile, K15B units across GA/GL/GXL variants share EGR valve carbonisation (part 13510-87A00) due to identical intake routing and stop-start duty cycles. Diesel D13A engines - used in early GA/GL trims - suffer common injector seal failure (part 19210-85G00) across markets, with identical high-pressure pump (part 19200-85G10) vulnerabilities in all 75PS/90PS outputs.
Engine families are consistent across trim levels (GA/GL/GXL/ZXi) within generations. Compatibility is defined by chassis and drivetrain architecture - not variant names.
All K-series engines share the same engine mount configuration (front: 12310-87E10, rear: 12360-87E20), enabling cross-generation swaps with minor wiring adaptations for MP-series CAN bus integration.
Used Ertiga engines carry significant risk due to series-wide failure patterns: K14B units often lack tensioner updates, while D13A diesels suffer unaddressed injector leak-down. For reliable operation, remanufactured engines with OEM-upgraded components are strongly recommended across all generations.
All rebuilt units undergo compression, leak-down, and 2-hour hot-idle testing to OEM tolerances (220-240 psi, ≤5% variance), validated against Suzuki ISTA+ diagnostics for the full Ertiga range.
Our UK stock includes fully reconditioned K14B and K15B engines, with D13A diesel units available to order. Every engine is rebuilt to series-wide technical standards - not variant-specific shortcuts.
All engines complete 4-hour dynamometer validation simulating mixed urban/highway loads (25-120 km/h cycles) with real-time oil pressure, temperature, and misfire monitoring - ensuring reliability across GA, GL, GXL, and ZXi configurations.
Every reconditioned Ertiga engine includes a 12-month parts-and-labour warranty covering core components across all trim levels and model years.
Engine Finders is a price comparison and referral service. Warranty terms are set and honoured exclusively by our certified UK workshop partners. Final coverage is confirmed in writing prior to purchase and varies by engine family, mileage, and service history.
When your engine fails, Suzuki Ertiga engine works can restore performance at a fraction of the cost of a brand-new engine. From diagnostics to rebuild, here's how experts ensure optimal results.
1. Diagnostics & Disassembly: Use Suzuki-specific scanner (Tech2 compatible) to log K15B cam phaser codes P0011/P0016 before teardown. Engine fully disassembled with torque-spec documentation per manual ENG-K15B-2020.
2. Block & Head Inspection: Cylinder bore measured for taper; K15B blocks with >0.05mm wear are rejected. Heads checked for warpage - max 0.05mm per Suzuki spec 11-301.
3. Critical Component Replacement: All K15B rebuilds include OEM cam phaser (18220-85G00), timing chain (13540-85G00), and oil pump (15100-85G10) per TSB ENG-2021-09 to prevent recurrence.
4. Precision Machining: Crankshaft ground only if journal wear exceeds 0.02mm. All K15B blocks honed with plateau finish (Ra 0.4-0.6µm) for proper ring seating - critical for Ertiga’s stop-start system.
5. Assembly & Torque Sequence: Head bolts torqued in 4 stages (25Nm + 90° + 90° + 50°) using calibrated angle gauge. Oil galleries flushed with solvent to remove casting residue unique to F42 chassis.
6. Post-Rebuild Validation: Cold start test, oil pressure verified at 3.5 bar idle, compression logged, and 30-minute hot idle cycle to check for K15B-specific oil consumption issues before delivery.