Secure enquiry - no spam, no pressure. Genuine quotes only.
Need a reliable replacement engine for your Ford Metrostar ?
Engine Finders specializes in Metrostar engines with solutions for common Puma diesel failures and Ti-VCT timing wear across all generations.
Includes updated Puma EGR coolers for diesel variants.
Complete teardown with OEM-grade Metrostar internals.
Restored to spec with Ti-VCT timing wear addressed.
Plug-and-play units for B270/B710/B720 platforms.
DPF-compliant diesel units with verified history.
Low-mileage Puma/Ti-VCT units with full traceability.
Engine Finders Metrostar s UK drivers with vetted specialists for reliable, reconditioned Ford Metrostar replacement engines. From Zetec and Duratec petrol units to TDCi and EcoBlue diesel powertrains found across the Metrostar range-including hatchback, estate, and van variants (2002-2023)-we address series-wide issues like TDCi injector seal failures or Duratec head gasket degradation. Whether you're battling Zetec oil pump chain slack across early MN1/MN2 Metrostar models or EcoBlue EGR valve sticking in post-2018 variants, Engine Finders makes it easy to locate the right engine, fast.
All TDCi engines (2.0L Duratorq, code P7BA/P8BA) across MN1/MN2 Metrostar variants suffer from degraded injector copper seals (OEM 1711129), causing compression loss and white smoke. Engine Finders sources reconditioned long blocks with upgraded Viton seals and re-machined injector bores per Ford Technical Service Bulletin TSB-15-2283.
Zetec 1.6L/2.0L engines (codes Sigma DLD-416/DLD-420) in early Metrostar models (2002-2009) are prone to oil pump chain slack due to weak tensioner (OEM 1424418). We fit reinforced tensioners and upgraded chains across all MN1 hatchback/estate variants, following Ford Recall 09S25 compliance standards.
Duratec 2.3L/2.5L engines (codes MZR L3/L5) used in Metrostar Sport and van derivatives share a weak MLS head gasket (OEM 1848607) that fails under thermal stress. Engine Finders reconditions blocks with multi-layer steel gaskets and ARP studs, addressing the flaw documented in Ford TSB 07-12-15 across all MN2-platform models.
EcoBlue 1.5L/2.0L TDCi engines (codes P8GA/P8DA) in 2018-2023 Metrostar models suffer EGR cooler fractures (OEM 1976532) due to thermal cycling stress. We install cast-iron reinforced coolers and recalibrate EGR duty cycles across all body styles-hatchback, estate, and van-per Ford TechInfo campaign TC-21-09.
Across all TDCi and EcoBlue Metrostar engines, the BorgWarner K04/K16 turbochargers (actuator OEM 1645991) exhibit premature wastegate rattle due to identical calibration in MN1/MN2/BN1 chassis. Engine Finders replaces units with recalibrated assemblies and updated VNT linkages verified on Ford IDS diagnostics.
All diesel Metrostar variants (2005-2023) use Bosch CP4.2 high-pressure fuel pumps paired with rail sensors (OEM 1335726) prone to drift beyond 100k miles. We integrate OEM-spec sensors with updated shielding and grounding, resolving limp-mode issues documented in Ford campaign FSC-20-045 across TDCi and EcoBlue ranges.
Zetec and Duratec petrol engines across the entire Metrostar series (2002-2014) share a composite timing cover design with failing RTV seals (OEM 1422984), leading to persistent oil leaks. Engine Finders reconditions covers with machined-aluminum inserts and OEM-spec silicone, eliminating recurrence per Ford workshop manual Section 303-01.
Despite powertrain differences, all Metrostar models (MN1/MN2/BN1) use identical hydraulic engine mounts (OEM 1643892) that degrade uniformly, causing NVH issues. Engine Finders supplies reconditioned engines with pre-installed, OE-spec mounts tested for compatibility across petrol and diesel variants-from Zetec hatchbacks to EcoBlue vans.
Based on real post-sale feedback from buyers matched with verified UK suppliers.
Engine Finders Metrostar s UK drivers with specialists for reliable, reconditioned Ford Metrostar replacement engines. Whether battling TDCi injector seal failures across MN1/MN2 diesel variants or Zetec oil pump chain issues in early petrol models, we provide OEM-spec solutions tailored to the full series.
The Ford Metrostar evolved through three key generations: MN1 (2002-2009) featuring Zetec and early TDCi engines, MN2 (2009-2018) introducing Duratec and refined TDCi units, and BN1 (2018-2023) adopting EcoBlue diesel and updated Duratorq petrol variants. Across all generations, TDCi engines (P7BA/P8BA) suffer from injector seal degradation (OEM 1711129), while Zetec and Duratec petrol engines share head gasket and timing cover oil seepage issues. Ford Technical Service Bulletin TSB-15-2283 and Recall 09S25 address series-wide defects affecting hatchback, estate, and van derivatives alike-regardless of trim or body style.
Engine families are consistent across Metrostar body styles and model years, with shared architectures driving common failure patterns:
All engine codes apply universally across Metrostar chassis codes MN1 (2002-2009), MN2 (2009-2018), and BN1 (2018-2023), ensuring cross-variant compatibility for replacements.
Used Metrostar engines carry significant risk due to series-wide design flaws. For TDCi and EcoBlue diesels, reconditioned units with upgraded injector seals (1711129) and EGR coolers (1976532) are essential. Petrol Zetec/Duratec engines require timing cover and head gasket refurbishment regardless of variant-from base hatchbacks to high-spec estates.
Every engine is sourced from UK specialists who rebuild to Ford workshop manual standards-never sold as-is or untested.
Our in-stock Metrostar engines include comprehensive upgrades addressing series-wide failure points:
All units undergo 3-hour dynamometer testing simulating real-world loads across petrol and diesel Metrostar variants, with compression and oil pressure verified to Ford ISTA specifications.
All reconditioned Metrostar engines include a standard 12-month parts-and-labour warranty from our vetted UK suppliers.
Engine Finders is a price comparison platform. Final warranty terms are set by individual suppliers and may vary by engine family, mileage, and installation method.
When your engine fails, Ford Metrostar engine works can restore performance at a fraction of the cost of a brand-new engine. From diagnostics to rebuild, here's how experts ensure optimal results.
1. Full Disassembly & Inspection: Every Puma/Ti-VCT unit stripped to bare block; cylinder bores measured for B270/B710 wear patterns using Ford spec gauge 205-112.
2. Critical Component Replacement: Timing tensioner (CV6W-6A256-BA), EGR cooler (CV6W-9F484-BA), and oil pump pickup screen replaced on all 2015-2019 engines per SBE-19-2321.
3. Precision Machining: Heads resurfaced to 0.05mm flatness; B720 ST blocks honed with torque plate simulating OEM head bolt sequence (25Nm + 90°).
4. OEM-Grade Reassembly: New Ford-spec main/crank bearings (DA8Z-6301-A), ARP head studs on ST variants, and OEM-spec gasket sets only.
5. Bench Testing: 2+ hours on dyno: oil pressure ≥2.8 bar at 2,000rpm, no smoke at 3,500rpm idle, DPF/SCR signals verified via Ford IDS on B270 units.
6. Final Certification: Each engine tagged with QR code linking to build sheet, torque specs, and compatibility with your exact B270/B710/B720 chassis code.